Guide
How to choose safety shoes: EN ISO 20345 classes explained
A buyer's guide to the safety footwear classes named in most UAE site specifications, and the details a supplier needs to quote safety shoes correctly.
Most RFQs for safety shoes in Dubai, Abu Dhabi and Sharjah mention EN ISO 20345 and a class such as S1 or S3. The class is shorthand for a bundle of features. Knowing what is in each bundle lets you ask for the right pair instead of the most expensive one, and it removes a round of emails with the supplier.
What EN ISO 20345 covers
EN ISO 20345 is the European standard for safety footwear. As summarised by footwear makers, it sets requirements and test methods for shoes and boots with a toe cap that is tested for impact at 200 joules and compression at 15 kilonewtons. Everything that follows is built on top of that basic toe protection.
The classes at a glance
- SB: the basic class. Toe cap at 200 J impact and 15 kN compression, plus slip resistance on ceramic tiles with a detergent solution. Closed seat region, antistatic properties and seat energy absorption are optional at this level.
- S1: SB plus a closed seat region, antistatic properties and energy absorption in the seat region.
- S2: S1 plus resistance to water penetration and water absorption of the upper.
- S3: S2 plus a penetration-resistant insert in the sole and a cleated (treaded) outsole.
A 2022 edition of the standard added classes S6 and S7, which a manufacturer describes as footwear with a waterproof feature such as a membrane. Check which edition your site rule cites.
The sources below also describe non-metallic penetration-resistant inserts as a variant, so a buyer who wants a metal-free midsole should say so in the request.
Reading the extra markings
A pair marked to a class can carry further letters, for example P for penetration resistance or SR for an additional slip test on glycerol. Treat extra letters as separate requirements. If your site rule says “S3 with SR”, write exactly that in the RFQ so the supplier does not assume the basic S3 is enough.
Choosing by workplace
- Dry indoor floors, warehouses and workshops: buyers often start with S1 or S1P and add the features their risk assessment names.
- Wet or washed floors, or outdoor work with splashes: the water penetration feature of S2 or S3 becomes relevant.
- Construction sites, rough ground and sharp debris: the penetration-resistant sole and cleated outsole in S3 are the reason that class appears on many site lists.
- Electrical work: antistatic properties are not the same as electrical insulation. If your task involves live work, say so and ask for the specific footwear your electrical safety rules require.
These are common buying patterns, not rules. Your HSE officer, client specification or site induction decides.
Toe cap material, weight and comfort
Steel, aluminium and composite toe caps can all be built to the same class. The class tells you how the cap performs when tested, not which material it is. State the material if you have a preference, for example metal-free for airport style security checks. Weight and fit matter on long shifts, so ask for a sample size or a datasheet if you are standardising footwear across a crew.
Size runs and gender fit
For a project order, give a size split rather than one total. The catalogue lists safety shoes in sizes 38 to 49. A split such as 20 pairs of size 42 and 30 pairs of size 43 gives a quotation you can confirm quickly. If a crew includes women, say so, because fit differs by last.
Reading a site rule step by step
Suppose a site rule says “safety footwear S3”. Using the class descriptions above, that line means a toe cap tested at 200 J and 15 kN, a closed seat region, antistatic properties, seat energy absorption, resistance to water penetration and absorption of the upper, a penetration-resistant insert in the sole and a cleated outsole. Ask the project whether it wants all of that or whether S1 or S2 would satisfy the rule. Many rules are written for the worst area on a site and then applied to every worker.
Common mistakes in safety shoe orders
- Treating the class as a quality ranking. The classes describe features, not grades of manufacture.
- Choosing by the toe cap alone and forgetting the sole and upper.
- Ordering one style for a mixed crew. Drivers, welders and electricians may need different footwear.
- Skipping a sample. Fit differs between lasts, so a trial pair saves returns across a large order.
- Leaving out replacement. Decide how worn pairs will be replaced and keep the same model if you can.
Questions to ask any supplier
- Which class and extra markings does the offered model carry, shown on its datasheet?
- Is the penetration-resistant insert metallic or non-metallic?
- Which sizes are offered, and are half sizes available?
- Is a sample pair available before the order, and how long does it take?
- Which documents come with the goods?
What to put in the RFQ
- Class and extra markings your site names (for example S3, SR)
- Toe cap material, if you have a preference
- Upper style: shoe, ankle boot or high boot
- Sole requirements, such as oil resistance or heat resistance, if your site needs them
- Size split and total quantity
- Delivery site in the UAE or GCC and the date you need the shoes
- Brand preference, or “equivalent” if you accept alternatives
Send the same details for steel toe safety shoes or any other style. The PPE RFQ checklist lists the fields for a mixed order that includes shoes, helmets and gloves.
What this guide does not do
It does not state that any pair we quote meets a class. It also does not replace your own risk assessment. If a standard matters to your approval process, name it in the request and ask for the datasheet and marking for the exact model offered.
Ready to quote?
Send the item, specification, quantity and delivery location. Open the quote form with this topic filled in, or email sales@vmv-solutions.com.
Frequently asked questions
Is S3 always better than S1?
No. S3 adds a penetration-resistant midsole and a cleated outsole to the S2 features, which suits rough ground and sharp debris. For an indoor warehouse or workshop floor those extras may not be needed. Choose the class your risk assessment or site rules name.
What does the SB marking mean?
SB is the basic class. It carries the toe cap requirement and the other basic requirements, and the extra features of S1 to S3 are not required.
Do I have to buy steel toe caps?
The class describes how the toe cap performs, not what it is made of. Toe cap material is a separate line in your request, so state it if your site cares.
What size range should I request?
Give a size split. The catalogue lists safety shoes in sizes 38 to 49, and a split by size avoids a second round of questions.
Does this page say your shoes meet EN ISO 20345?
No. This guide explains what the classes mean. Name the class in your request and the quotation states what can be supplied against it.
Sources
uvex: safety footwear standards | SHP Online: safety footwear standards and ratings | uvex: changes in the 2022 edition | Ejendals: EN ISO 20345
