Guide
Safety glove selection: EN 388 and EN 407 markings explained
Read the pictogram on a glove, match the material to the task and give a supplier the details it needs to quote safety gloves in the UAE.
Glove RFQs go wrong in two ways: a buyer asks for “cut-resistant gloves” without a level, or a supplier quotes a glove with a pictogram nobody on site understands. This guide covers the two markings buyers name most, EN 388 for mechanical risks and EN 407 for heat, then shows how to turn them into a request.
EN 388: gloves against mechanical risks
EN 388 sets requirements, test methods and marking for protective gloves against mechanical risks. The tests named by the standard include abrasion, blade cut, tear and puncture resistance. On a glove the pictogram is followed by a code of four numbers, then a letter, then sometimes a second letter.
As explained in the 2016 version summaries, the positions read as follows.
- Position 1: abrasion resistance, a number up to 4.
- Position 2: blade cut resistance by the coupe test, a number up to 5.
- Position 3: tear resistance, a number up to 4.
- Position 4: puncture resistance, a number up to 4.
- Position 5: cut resistance by the TDM test (ISO 13997), a letter from A to F.
- Position 6: the letter P appears only when impact protection has been tested.
A higher number is a higher test level. An X means the property was not tested. Because every position is a separate test, two gloves with the same cut digit can differ in puncture or tear. Compare all positions with the hazard on your site.
EN 407: gloves against thermal risks
EN 407 covers protection against heat and fire. The pictogram carries six numbers in a fixed order.
- Burning behaviour: how long the glove keeps burning or glowing after the flame is removed.
- Contact heat: how fast heat passes through the glove when it touches a hot surface.
- Convective heat: how long the glove delays heat from a flame.
- Radiant heat: how long the glove delays heat from a radiant source.
- Small molten metal splashes: how many small drops it takes to heat the inside.
- Large molten metal splashes: the amount of molten metal that affects the skin side.
Each is scored from 0 to 4 in the sources used here. A zero is a fail and X means that property was not tested. Welding and heat work usually need a specific property, such as contact heat or molten metal, not an average of all six.
Match material to task
The old catalogue lists these glove materials, and each fits a different kind of job.
- Cotton and fabric gloves: light handling and general housekeeping.
- Coated fabric gloves: grip for dry or oily handling, with the coating chosen by the task.
- Leather gloves: general site work and welding styles.
- Latex, rubber and plastic gloves: wet work and many chemical tasks, subject to the chemical.
- Kevlar gloves: cut-prone work such as sheet metal and glazing.
- Butyl rubber gloves: certain chemicals, if your chemical safety data names this material.
- Vibration and impact gloves: tools and heavy handling.
- Aluminized gloves: radiant heat.
The material is a starting point only. For chemicals, read your safety data sheet and name the chemical in the RFQ.
Sizes and fit
Gloves that are too large reduce grip and too small tire the hand. The catalogue lists sizes in groupings from XS-S to XL-XXL. A size split, such as 30 medium, 50 large and 20 extra large, speeds the quotation.
Reading a marking, step by step
Take a glove marked with the EN 388 pictogram and the code 4 3 4 2 C P. Position by position, using the key above, that reads as an abrasion level of 4, a blade cut level of 3, a tear level of 4 and a puncture level of 2, a TDM cut level C and an impact test passed. The example is made up to show the method, and it is not a glove we quote. If your task is mainly cutting, look at the cut positions first. If it is puncture by nails or wire, look at position four.
Common mistakes in glove orders
- Using one glove for every task. Gloves that suit dry handling may not suit oily parts, heat or chemicals.
- Looking only at the highest number. A high cut level can come with lower dexterity, and the task may need grip more than protection.
- Mixing up standards. EN 388 does not cover heat, chemicals or cold.
- Forgetting liners and cuffs. Heat and welding work need cuff length.
- Not trialling sizes. Fit affects grip and fatigue, so a size trial pays off in a large order.
Questions to ask any supplier
- Which markings does the offered glove carry, as shown on its datasheet?
- Which edition of the standard was the testing under?
- What is the coating or material, and is it suited to oil, water or chemicals?
- Which sizes are available?
- Is a sample available before the order?
Writing the glove request
- Task and material handled (sharp, hot, wet, chemical, oily)
- Rating you need, written in full, for example “EN 388 cut level C” or “EN 407 contact heat level 2”
- Material and cuff style
- Size split and quantity
- Delivery location and date
- Brand preference or “equivalent”
Use the same fields for a safety gloves enquiry and for a mixed list in the PPE RFQ guide. If the markings on a sample matter to your approval, ask for the datasheet of the exact glove offered.
What this guide does not do
It explains the markings. It does not say that any glove we quote carries a given level. State the level you need, and the quotation names what can be supplied.
Ready to quote?
Send the item, specification, quantity and delivery location. Open the quote form with this topic filled in, or email sales@vmv-solutions.com.
Frequently asked questions
What does an X in a glove marking mean?
An X in place of a number means that property was not tested. It is not a low score, it is no score.
Is a high cut level enough for all sharp work?
Not on its own. Cut, puncture and tear are separate ratings, so a glove with a high cut level can still have a low puncture level. Read all positions against your task.
Does EN 388 cover chemicals?
No. EN 388 is for mechanical risks. Chemical protection is covered by a different standard, EN 374, so name it separately in your request.
Which glove sizes do you list?
The catalogue lists safety gloves in XS-S, M, L and XL-XXL groupings. Give a size split with your quantity.
Does this page say your gloves carry these ratings?
No. It explains how to read the markings. The quotation states what can be supplied against the rating you name.
Sources
uvex: EN 388 glove standard | BSI Knowledge: protective gloves against mechanical risks | Atom: EN 407 heat resistant gloves
